Cut your energy bill with the data you already have.
Zebblo works with the energy data your site already has. We find waste, tariff leaks and penalties, tell your team what to change first, and verify every saving. Start with the data you already have. Where there is none, we install a small kit for the pilot.
Your electricity bill hides money you can save.
Most energy-intensive sites pay more than they need to. The reasons rarely show up in a monthly bill.
- Heavy loads run when power is most expensive.
- Many machines start together and push up demand charges.
- Power-factor penalties repeat every month.
- Equipment runs when nobody needs it.
- Diesel generators run longer than necessary.
Dashboards show the numbers. They do not tell you what to do, or prove that it worked.
From bill to verified saving, in three steps.
Each step builds on the one before. You can start with nothing more than your electricity bills.
See where the money goes.
Share 12 months of electricity bills. Add interval meter data or exports from systems you already have. Where your site lacks detailed data, we install a small kit for the pilot.
Zebblo learns what each site should use, given the weather, the calendar, your volume and your operating hours.
Act on the biggest items first.
Every finding comes with its cost per month, the likely cause and the steps to check on site. Your team knows what to look for before anyone walks the floor.
Each action goes into a log with an owner and a due date.
See the saving, not an estimate.
Zebblo compares what you use with what you would have used without the changes, following IPMVP, the international method for verifying savings.
You get a monthly savings statement you can show your management, your auditor or your bank.
One clear page per stage, in rupees.
- 1Move laundry and pre-cooling out of 5 pm to midnight₹14,000per month
- 2Stagger chiller starts: peak down 60 kVA₹18,000per month
- 3Correct power factor from 0.91 to 0.99₹21,000per month
Modelled from 12 bills · confirmed after action
Runs most of the peak-tariff hours at under half load, alongside chiller 1.
Pre-cool from 3 pm to 5 pm, then run one chiller at full load after 5 pm.
Battery charges at midday, discharges in the peak. Your team or vendor runs the plan; Zebblo checks it was followed.
Illustrative screens for a mid-size hotel. Figures are examples, not results.
Built for the people who own the energy bill.
A saving needs a yes from more than one person. Zebblo gives each of them what they need to say it.
Know what you will get back.
- Savings shown in money, not kWh
- A monthly fee sized to your savings. Your savings are about 3 times the fee
- One monthly statement for management
Save without risking product or process.
- Recommendations respect temperature and process limits
- Zebblo never switches your equipment
- Fewer alarms, each with a cost and a likely cause
Do more for every client.
- Run your analysis across every client site
- Show clients verified results
- Earn a referral fee or a share of revenue
Energy management usually stops at the dashboard.
Zebblo does the analysis and the follow-up for you, so your team spends its time on the machines and sites where the money is.
Two products. One goal: lower energy cost.
We analyse your energy, tell you exactly what to change, and verify the result every month.
Explore OptimizeWe turn the same data into evidence for ISO 50001, the German Energy Efficiency Act, energy audits and sustainability reports.
Explore Audit & ReportMade for sites where energy is a major cost.
We start with what you already have.
Bills, your utility smart meter, building systems and business systems such as hotel bookings or a warehouse management system. Where there is none, we install a small kit for the pilot.
Ways in which your data reaches Zebblo.
Up to 32 devices share one cable. Add meters, sensors or later a controller, with no new wiring.
Checks every reading, applies your tariff, finds and ranks savings, verifies results.
- Monthly savings report
- Alerts on WhatsApp or email
- Action log for your team
Device types only. IoT: Internet of Things. RS-485: the standard industrial data cable. UPS: Uninterruptible Power Supply. PLC: Programmable Logic Controller. BMS: Building Management System. SCADA: the control and monitoring system of a plant. Existing meters and systems are reused when they can export data.
Your data stays yours.
We read. We never write.
Zebblo only reads data. Our meters only measure and never switch equipment. Automatic control comes later, only when you choose it.
Access you can withdraw.
You decide what we see, and you can withdraw access at any time. We never share anything that identifies you.
Every number has a source.
Each saving shows its baseline, its method and the actions behind it.
Your first findings, free, in 5 working days.
Send us your bills. The founder reviews every Scan personally.
Send 12 months of bills and tell us about your site and what you report on.
We look at your tariff, demand charges, power factor and diesel use.
You get the top savings in rupees and the data that would add more detail. Then you decide on a 2-month pilot.
Still have questions?
Do I need to install hardware?
Not to start. The free Scan uses your bills only. Where your site lacks detailed data, we install and lend a small kit for the 2-month pilot.
Does Zebblo control my equipment?
No. Zebblo recommends actions. Your team decides and carries them out. Automatic control comes later, only when you choose it.
How do you know the savings are real?
We agree a baseline with you before we start and correct it for weather, volume and operating hours. We follow IPMVP, the international method for verifying savings.
Is Zebblo right for the size of my site?
Zebblo fits sites where energy is a major cost, from a single hotel or cold store to a multi-site group or a large plant. The free Scan tells you quickly whether it fits.
See where you could save on energy.
or write to us at abhishek@zebblo.com to discuss your specific needs.
Alternatively, share your email address and we will reach out.